基于大型打桩船桩架的三维力学特性分析

应用国际广泛使用的大型通用结构有限元分析程序ALGOR对110m大型打桩船桩架进行了三维力学分析,该装备是国内最高并在海上施工的桩架,因此对各工况进行了详细的分析研究,并给出了合理的设计建议。对从事该领域设计施工者有一定指导作用。     

无锚板桩+支撑墩码头结构在强涌浪海域块石覆盖层条件下的应用

以色列阿什杜德港项目所处环境地质条件差,覆盖层以0~3 t块石为主;风浪条件恶劣,季风期有效波高达5 m以上。前期人员、设备、材料等出海的施工码头建设十分困难。通过综合分析比较高桩码头、抛石堤码头及板桩码头等传统码头形式的特点,经科学的设计创新采用无锚板桩+支撑墩结构形式码头,同时采取安全可靠的施工技术,高效、安全地完成施工码头的建设。     

重力式方块卸荷板大型构件出运码头升级改造

以工程实例介绍了重力式方块卸荷板码头的改造设计方案。由于原有码头卸荷板悬臂较大,在码头前沿均布荷载增大的情况下,使得基床顶面产生较大的后倾应力,基床承载力不满足规范要求。改造方案通过在后方设灌注桩及现浇钢筋混凝土板,减少码头卸荷板悬臂部分上部荷载,防止基床顶面产生较大的后倾应力,为类似的码头改造设计提供了借鉴。     

湛江深厚老黏土地区钢管桩沉桩规律

对湛江老黏土地基5个工程钢管桩施工进行总结,得出以下结论:老黏土地区持力层宜选择50击的中粗砂层或者40击以上黏土层,此时基桩承载力恢复系数为1.26~1.40,比一般黏性土高;打桩锤宜选择D128、D138柴油锤,二档档位终锤贯入度宜为2~5 mm击,三档档位终锤贯入度为6~10 mm击,能量传递系数为28.5%~47.6%;当持力层和桩锤符合上述情况时,直径在1 000~1 400 mm的钢管桩总锤击数小于2 500的占统计83.8%,打桩效率最高。     

不同土质下预制方桩沉桩承载力特性分析

对沿海地区某码头预制方桩沉桩过程进行监控。结果表明,打桩时由于桩周土扰动剧烈,桩的贯入阻力大幅减小,粉质土贯入阻力降低比例高于粉砂。复打测试表明:粉质土的恢复系数较粉砂高;桩侧摩阻力与土层性质密切相关。在沉桩时可根据土层情况选用合适的打桩锤击力,以减小或避免对桩的不利影响。     

冲孔灌注桩施工质量控制要点

冲孔灌注桩因其适应性强、成本适中、施工简便等优点，广泛应用于公路桥梁工程建设中。文章详细介绍了冲孔灌注桩成孔、成桩施工各环节的质量控制要点，为类似桩基施工提供技术参考。     

桥梁桩基础施工技术探讨

桥梁桩基础是整个桥梁的重要组成部分,稳定夯实的桥梁桩基础对桥梁起到了重要的支撑作用,桥梁桩基础的质量好坏对整座桥梁的工程质量具有直接的影响.以某桥桩基施工为例,探讨钻孔桩施工技术以及需要注意的重要问题,以供同行参考.     

搅拌桩处理公路软弱地基施工工艺的探讨

以搅拌桩工艺处理软土地基,使其承压性能达到道路施工的必要条件。基于工程实践对其使用工艺进行技术优化,对于提高作业效率和降低工程成本是十分必要的。     

Corrosion rate measurements in steel sheet pile walls in a marine environment

Corrosion of steel structures in the marine environment is a major problem. The deterioration of this kind of structures is costly and difficult to predict both when designing new structures and when estimating the remaining service life time for existing structures. The aim of this investigation was to find indicative values for the corrosion rate of steel sheet piles on the Swedish west coast. Such corrosion rates (mm/year) can be used both when designing new structures by oversizing the steel thickness and when estimating the bearing capacity of existing sheet pile structures. Earlier investigations on the corrosion rates along the Swedish east coast – with salinity from about 0.2% to 0.8% – are still used today as guidelines for the corrosion rate of all steel structures in the Swedish maritime environment even though the salinity on the west coast can be as high as 3.0%.Steel sheet pile wharfs located in the port of Halmstad on the Swedish west coast were inspected by ultrasonic measurements. Three wharf structures with a total length of about 700 m were inspected. None of the inspected wharfs had or have had cathodic protection. The thickness measurements of the steel sheet pile structures were performed by divers.The age of the three inspected sheet pile structures ranged from 36 to 51 years. The dimensions of the original sheet pile sections are known. One of the quay structures is located along a river. The salinity at all wharfs varied from low values at the surface to approx. 2% at the bottom (also in the river outflow).The measured average corrosion rates were in the same order as the design values in the European code. However, the results indicate increased corrosion rates about 1 m below the mean water surface and at the level of the propellers from the ships berthing the most frequented of the inspected wharfs, 3–6 m below water surface.The tolerances of steel sheet thicknesses – usually in the order of ±6% – are often neglected when investigating the remaining thickness in steel sheet piles. A simple calculation model shows that the sheet pile must be almost 50 years of age before an accurate estimation on the corrosion rate can be made, considering the tolerances, if the true original sheet pile thickness is not known.     

高铁湿陷性黄土隧道地基处理浅析

根据湿陷性黄土隧道工程特点,结合宝兰客专客运专线王家岔湿陷性黄土隧道地基加固处理的工程实例,阐述了洞口和洞内两种施工工艺不同的水泥土挤密桩施工方案,分析了隧道内水泥土挤密桩施工对其它工序的干扰和对工期的影响,以及施工振动对初支结构和围岩稳定的危害,提出了有效的控制措施.